Comments on: Packard Bell Easynote Keyboard Replacement MZ35/MZ36

By: john o neill

john o neill — Wed, 10 Feb 2010 18:54:54 +0000

Packard Bell Model ETNA-GM how does one remove the case, I have got as far as the hinges rear section and unable to go any further I want to open it to have a look at power port which does not no longer make physical contact with its power input.
thanks John

By: ninjaneer

ninjaneer — Wed, 03 Feb 2010 13:24:30 +0000

I have been pointed to this disassembly manual for the "V Series Sable Chassis". I don't have an MV35 here to compare with so I can't say for sure that this service/disassembly manual matches up with your laptop. If you find that it does, please let us know here. Note that the MV35 is not the same chassis as the MZ35/36

By: nigel lamb

nigel lamb — Wed, 03 Feb 2010 13:09:38 +0000

hi i have a packard bell mv35-202 which has no power at all either from the battery or from the mains lead, i think i will need to replace the mother board as think the power card has gone, do you know where i can down load a dissasembly manual / instructions for this lap top,also do you know where the best place to purchas a new mother board. thanks

By: jyson109

jyson109 — Thu, 05 Nov 2009 23:41:14 +0000

one of the buttons has gone on the touch pad is there a simple way instead of taken all the rest of apart

By: JohnW

JohnW — Thu, 05 Nov 2009 13:55:41 +0000

Thanks very much for this – I would not have known where to start otherwise. My model was an MZ35 purchased in Europe – a minor difference in the casing was that there are two keyboard retaining screws on the underside, and they were both marked with a K

By: jacklord

jacklord — Sat, 24 Oct 2009 15:03:10 +0000

my laptop packard bell easynote MV35-202 has been in the repair shop twice to get the same soldering job carried out, each time cost £40.00, (i now do not trust the shop) where the power lead fits into the laptop it is that part of a small pc board which is giving me problems with dry joint/s which results in swiching the power off or causing it to crash although i can solder perfectly well, i have only managed so far with getting at the small pcb. is there a free manaual available to dissemble the laptop so i can repair it myself or will i have to purchase. thankyou.

By: Emile

Emile — Sun, 20 Sep 2009 17:37:59 +0000

Thanx, it helped me well….lol!

By: RawData

RawData — Sun, 13 Sep 2009 12:09:45 +0000

PB FTPadmin probably hates me now, but I found the correct dissassembly manual. Four clips holding the keyboard are way too tough to handle without breaking them. However, I found the faulty part (LCD cable) and it’s close to impossible to fix and replacement not available anywhere near here, so the laptop is considered as toast. No commerse via net for me, so I’ll let the owner decide what to do with this.

Still, thanks for pointing out PB FTP server for me.

By: RawData

RawData — Fri, 11 Sep 2009 11:10:17 +0000

As there are over four thousand directories there, finding disassembly manual for particular model (P/N: PB91QD0091) is going to take a while! Findind the exact item number would be nice, as otherwise the task is next to hopeless. Lets see what FileZilla’s “Find” function has to say about it…

Hopefully it’s just dirty connector or loose graphics card and not the infamous nVidia hardware bug…

By: David

David — Mon, 17 Aug 2009 19:57:31 +0000

TO meimmi132 (and anyone else whos interested)

Here is a link to the the dissasembly instructions forpackard bell easynote mz series…

ftp://ftp.packardbell.com/pub/itemnr/7602080000/Disassembly_EasyNote_MZ_rev_100.pdf

hope this is useful.